Wood cleaning products
Woca Beige Applicator Pad for use with the WOCA Doodlebug Floor Applicator
The Woca Doodlebug incorporates a hook and loop base for strong attachment to the Woca Beige Applicator Pads. When applying and spreading the oil, it naturally generates heat and friction which forces the oil into the wood leaving the hardest of finishes.
Applicator Pad size: 115mm x 250mm / 20mm Thick
A moisture and sound resistant underlay for floating floors. Dual moisture barrier with 200mm overlap. Excellent levelling properties. Unique construction allows for efficient ventilation. 20dB reduction on transmitted impact noise. Compatible with underfloor heating. 3mm thickness. Available per m² or 33m² roll.
A highly water- and dirt-repellent oil for wood surfaces.
Worktop Gel is used to fresh up previously oil treated wood surfaces. The effective gel is quick-drying, enhances the colour and natural grain of the wood and gives a resistant and strong surface.
6-12 m2/l 68-129 sq.ft./l
How to apply
Clean the surface thoroughly with WOCA Wood Cleaner mixed with water in the ratio 1:40 and let it dry for at least 8 hours until the surface is completely dry. In case of grain raising, an advantage would be slightly to de-nib with fine sand paper, grit 220 (remove any sanding dust from the surface).
Spread a suitable layer of gel in an even, thin coat with a polishing pad (white, beige or red). Continue polishing until the wood appears saturated and the surface looks uniform. We recommend working in sections as the gel dries quickly.
Wipe off the polished surface carefully with a dry lint-free cloth before continuing to next area. The surface should not appear wet and there should not be any excess gel left on the surface after polishing. In case the wood does not seem completely saturated after 4-6 hours, we recommend re-polishing with a smaller quantity gel than by first treatment, but same procedure. Leave the worktop to dry for 4-6 hours, hereafter it may cautiously be taken into use. If possible, do not expose the surface to water during the first 2-3 days. We recommend leaving the worktop to harden for 3 days. After the hardening time, the surface can be cleaned with WOCA Natural Soap Spray and a lint-free cotton cloth.
The regular cleaning may be done with WOCA Natural Soap or WOCA Oil Soap which at the same time provides the wood with caring oil by each cleaning. Depending on wear, it is possible to maintain. Water spots and other minor damages are easily repairable by cleaning the surface locally with WOCA Wood Cleaner, let it dry and polish with a smaller quantity of Worktop Gel on a lint-free cloth.
Natural Soap is ideal for cleaning and maintenance of oiled, waxed and natural soaped surfaces. Natural Soap is a pre-mixed quality soap, which due to its nourishing properties quickly closes the pores of the wood and protects against dirt and penetration of liquids. Natural Soap white and grey are recommended for surfaces treated with white and grey oil, while Natural Soap natural is ideal for surfaces treated with natural or Colour Oil. The Spray makes the maintenance of oiled furniture, doors, table tops, panels, stairs, doors, etc. easier.
Availble in 0.75l
How to apply
Shake the spray well before use
Spray the Natural Soap on the surface.
Wipe the surface with a cotton cloth. Please note: Don't use microfiber.
Natural Soap is a purpose-made quality soap, which due to its nourishing properties quickly closes the pores of the wood and protects against dirt and penetration of liquids.
- Available in 1 Litre & 2.5 Litre
- Consumption: 320-400 m2/litre
- 1L Woca Wood Cleaner
- 1L Woca Vinyl & Lacquer Care
- 1L Woca Vinyl & Lacquer Soap
- 1 x Woca Lint Free Cloths
- Provides a strong water and dirt repellent surface
- Enhances the natural colour and grain of the wood
- Fast drying
- Delays emergence of mold and fungus
- Contains UV-protection
- Stir the oil thoroughly before use.
- Apply an even and thin coat of oil with the WOCA Applicator or a brush. Begin with the butt ends of the wood. The wet oil may have a white shade. When the water has evaporated after a few minutes, the wood will appear oiled.
- Wipe off any excess oil with clean cotton cloths after no more than 5 minutes. Take particular care in removing excess oil from joints and grooves.
- Repeat step 2 and 3 if the surface does not appear saturated with oil.
- When the wood is dry, it may be polished with a polishing pad or polishing machine to ensure an extra hardwearing surface.
- Depending on weather conditions and outdoor temperature it takes 24 to 48 hours for the oil to harden thoroughly. The wood must not be exposed to water during this period.
Our Unique and very cool Champagne Cork Stool. Made from Natural cork.
The seat is made from 100% natural cork, very Eco Friendly, 100% recyclable.
H 45cm x W 30cm
Free Delivery to mainland UK with this item.
Our Unique and very cool Bar Stool. Made from Natural cork with a steel frame.
The seat is made from 100% natural cork, very Eco Friendly, 100% recyclable with a steel base.
H 75cm x W 40cm
Free Delivery to mainland UK with this item.
Click Seal guards high-traffic floors against moisture damage. For both commercial and residential use. Prevents joint swelling. Quickly and easy installation: apply a bead to tongue of plank, then click together. Easily applied and excess lifts right off with no residue. New 125mm tube will cover 5 square metres of flooring
Wicanders Power Polish is a long-term maintenance product for the care of Wicanders Floors with HPS, WRT and PU acrylate UV. It is easy to apply and provides a protective coating.
- Size: Power Polish is sold in 1L containers
- Application: By short hair mop/wax applicator (Ex. LOBATOOL)
- Coverage: 3L will cover approximately 1000 sq.ft., depending on application rate
Power Polish Instructions:
- Make sure the floor is clean and dry; clean it with Wicanders® Soft Cleaner; a basic clean is recommended for Corkcomfort Floating WRT & HPS
- Apply one coat of Power Polish evenly, using a soft mop application tool. 3L will cover approximately 1000 sq.ft.
- Let the floor dry completely (about 30 minutes); do not polish after using the maintenance products
- Clean all tools with water, immediately after use
- The frequency of maintenance depends on the traffic and on the floor visual aspect
A moisture and sound resistant underlay for floating floors, with integrated DPM (Damp Proof Membrane) 19dB reduction on transmitted impact noise. Compatible with underfloor heating. Thermal Conductivity 0.045W 3mm thickness. Available per 15m² roll.
A highly water- and dirt-repellent oil for wood surfaces.
Worktop Oil is designed for untreated or previously oiled/sanded wood surfaces. The oil makes the surface highly water -and dirt-repellent. Use Worktop Oil, Natural, on both dark and light wood species – such as mahogany, merbau, teak, cherry, ash, oak, beech, maple, birch, pine etc. - to give the wood a mellow, golden colour. Use Worktop Oil, White, to lighten up the wood or give it a whitewashed effect.
12-15 m2/l 129-161 sq.ft./l
How to apply
If the surface is particularly smooth, sand the surface with sandpaper grit 180. Make sure the wood is dry and devoid of any dirt or grease. Clean the wood with Wood Cleaner. After cleaning, let the tabletop dry for at least 8 hours.
Stir the oil thoroughly before use. *Use a paintbrush to apply a suitable amount of oil in an even, adequate coat
Wait approx. 20-30 minutes at 20º C as the oil penetrates into the wood. If necessary, sand the wood while the surface is still wet with oil. Sand wet in wet lengthwise the wood grain with sandpaper grit 320-400. Next, wipe off all excess oil using a lint-free cotton cloth. Do not leave any excess oil on the surface.
Carefully polish the wood using a white polishing pad, which makes the surface more hard-wearing. *Repeat the treatment on highly absorbent surfaces. *The oil is thoroughly hardened after 24 hours at 20º C. Do not let the tabletop become wet during the hardening process. Maintenance: Use Worktop Oil to maintain the tabletop four times a year, or as often as necessary. Always clean the worktop first using Wood Cleaner. Follow the same procedure, but apply only one coat of oil. Risk of self-ignition: Due to the risk of self-ignition it is important that sanding dust and oil wetted cloths are soaked in water and disposed of in a tightly closed container after use.
Wood Lye may be used on all types of wood. Comes in White and Grey.
Spot Remover effectively dissolves grease, blood, coffee, tea etc. May be used on unfinished, soaped, oiled or waxed interior surfaces.
Spot Remover is based on soap and is specially developed for indoor use to remove spots from oiled wood surfaces.
Available in 0.25l
How to apply
Before using Spot Remover it is advisable to make a small test at a non-visible place of the floor to ensure that there will be no undesired reaction.
Spray Spot Remover evenly on the stain directly from the bottle. *Leave the Spot Remover to dissolve the stain for 10-20 min
Now scrub with a brush till the stain has been dissolved. *Wipe with cloth wrung in lukewarm water.
Repeat operation if necessary. *When the floor is completely dry apply the original surface finish, e.g. oil, wax or soap to re-establish the protection of the surface
WOCA Softwood Lye may be used for all types of soft wood such as pine, spruce, and pitch pine. Used on larch wood, an antique grey to brownish finish is created. WOCA Softwood Lye may not be used on hardwood.
By use of softwood lye on spruce the wood may assume a greenish colour which will disappear in the course of time
Pre-Colour is available in the container size of 2,5 litre container and in the colours white, extra white and grey.
Brush, plastic bucket and stick for stirring. Clean tools in water.
How to do...
The unfinished woodwork must be well sanded, clean and dry before application of the Pre-Colour. Clean with 125 ml Wood Cleaner mixed with 5 l water. Shake the container. Pour the Pre-Colour into a plastic bucket and stir regularly in order to obtain a uniform result.
Apply the undiluted Pre-Colour in an even layer length wise onto the floor with a paint brush. Use at least 1l of Pre-Colour per 10 m2. On vertically mounted woodwork, apply from top to bottom. Clean tools in water.
When the wood is dry, clean with Wood Cleaner and leave to dry or alternatively use green pad under floor machine and subsequently vacuum clean the floor. Finish the floor with Wood Floor Oil, Master Oil, Colour Oil, High Solid Master Oil or Oil Lacquer.
For making a one-coat application
There are 6 discs in a pack and each disc is 150mm in diameter with a Velcro back
Application area - With the introduction of the green WOCA Patina Discs, WOCA presents a new revolutionary way of oiling floors. By using the WOCA Patina Discs it is now possible to make a one-coat application of the floor. The surface is saturated immediately, becomes hard-wearing, silky smooth, and easy to maintain.
Result - The floor is well saturated, feels soft, dries quickly and has a silky-mat gloss. In order to achieve this result, we recommend using WOCA High Solid Master Oil, natural or white. The oil has a low content of solvent and fills the grains of the wood excellently. This guarantees a hard-wearing surface.
Available in Natural or White
Product size = 1 litre or 2.5 litre
Drying time: 2 hours at 20°C.
Coverage = 150 - 200 square metres per litre
Please Note, Oil Refresher may not be used on lacquered surfaces!
The Master Oil Natural is mainly used on dark wood species and enhances the natural warm glow of the wood whereas light wood species are often finished with Master Oil White which maintains and protects the natural light colour.
WOCA Maintenance Oil comes in natural and extra white or grey and may by used for all oiled wood surfaces and is especially suitable for the regular maintenance of oiled wooden floors.
Coverage is approximately 30 - 40 m2 per litre
Product, room and floor temperature should be between 15 and 35 degree C. Ensure good ventilation at all times during the application and drying time.
Clean the floor with 125ml Wood Cleaner mixed into 5 litre water. Leave the floor to dry for at least 8 hours. The floor must be completely dry.
Shake the container carefully. Apply approx. 1 dl oil per 4 m2 with pad, paint roller, cotton cloth or use polishing machine for large surfaces. It is important that the Maintenance Oil is carefully polished into the wood. Continue polishing until the wood appears saturated and the surface looks uniform.
Wipe the floor with clean, dry cotton cloths before proceeding with the next section of floor to be finished. The floor should not appear wet and there should not be any excess oil left on the surface after polishing. Continue stepwise till the floor has been finished.
When polished with polishing machine the floor will be pre-hardened after approx. 4 hours at 20 degree C and may cautiously be taken into use. Manually polished floors may be taken into use after 24 hours. Do not expose the floor to water during hardening time of 24 hours. Clean tools in Solvent. Risk of self-ignition: Due to the risk of self-ignition it is important that sanding dust and oil wetted cloths are wetted and disposed of in a tightly closed container after use.
Floor maintenance - How Often?
For domestic use = annually; For commercial use = twice a year.
If the floor looks extremely dry, we recommend treating the floor with Master Oil, or Diamond Oil instead.
WOCA Maintenance Box Natural Oil is everything you need to clean and torenovate your oiled wooden floor.
Each box contains:
- 1 x 1L Natural Soap - (Natural, White or Grey Soap*) is a purpose-made quality soap, which due to its nourishing properties quickly closes the pores of the wood and protects against dirt and penetration of liquids.
- 1 x 1L Maintenance Oil - (Natural, White or Grey Oil*) may be used for all oiled surfaces and is especially suitable for the regular maintenance of wood surfaces.
- 1 x 1L Wood Cleaner with spray
- 1 x Cotton Cloth
- 1 x Pad
*depending on your selection
Woca Intensive Wood Cleaner may be used for cleaning of lye treated, soaped, and oiled as well as lacquered surfaces. Furthermore, it is well suited for cleaning of unfinished wall- and ceiling panels, furniture etc.
How to apply
Unfinished and soap finished woodwork
1. 150 ml Wood Cleaner is mixed into 5l lukewarm water. Leave solution on surface to dissolve dirt if necessary. 2. Scrub with brush or pad manually or with floor machine if very dirty. Wipe clean with mop or cloth. 3. Repeat cleaning if extremely dirty. 4. If used on soaped surfaces, the protective soap shield is removed. Therefore, use Natural Soap as second step, when woodwork is completely dry.
Oiled woodwork and parquet floors
1. 150 ml Wood Cleaner is mixed into 5 l lukewarm water. Clean floor – leave solution on the floor briefly in order to dissolve dirt. 2. Scrub with brush or pad manually or with floor machine if very dirty. Wipe clean with mop or cloth. Repeat if floor is extremely dirty. 3. In areas with little wear, clean with Natural Soap. This brings back protective soap film against dirt. 4. In areas with more wear, it is recommended to maintain with Maintenance Paste/Oil.
Furniture, panels – lacquered, painted or otherwise finished
1. Mix 100 ml Wood Cleaner into 5 l of lukewarm water. Wipe surface with solution with hard-wrung cloth. Always wipe a second time to minimize the exposure to water of surface. Repeat operation if necessary. Please note: Don't use microfiber.
Tip: Always work with two buckets – one with Wood Cleaner mixed with water and one with rinse clear water.
Intensive Cleaner is a unique ready-to-use spray for the all-round cleaning of all interior wood work such as furniture, staircases, doors, panels and worktops independently whether the surfaces are oiled, waxed or lacquered. It provides an excellent cleaning and removes the most difficult dirt, grease and stains and is fast and simple to apply.
Available in 0.75l
How to apply
Before use, shake bottle of Intensive Cleaner carefully
Spray the Intensive Cleaner onto the surface.
Leave solution to dissolve stain and dirt etc.
Wipe surface dry with a firmly wrung cotton cloth. Leave surface to dry. Maintenance: Oiled surfaces are re-oiled with one of the WOCA oils. Waxed surfaces are re-oiled with the WOCA Maintenance Paste. Lacquered Surfaces are rejuvenated with WOCA Lacquer Care. Please note: Don't use microfiber. Tip: If extremely difficult stain, we also recommend WOCA Spot Remover.
Polishing machine is recommended for the polishing of bigger areas.
Coverage: 8 - 12 m2 per Litre / 20-30m2 per 2.5L
WOCA Driftwood Lye is a unique product, which gives the wood a weather beaten patina. The product is primarily for oak wood. By using this product, the wood will get a very nice 2 dimensional design. Finally, the surface must be treated with one of the WOCA oils. The product is water based and is available both in white and grey.
Its design and quality allows for regular professional use, it is equipped with a sturdy knuckle joint for even pressure on the floor and a tapered clamp for easy connection to a 24mm broom handle or similar.
The Woca Doodlebug incorporates a hook and loop base for strong attachment to the Woca Beige or White Applicator Pads. When applying and spreading the oil, it naturally generates heat and friction which forces the oil into the wood leaving the hardest of finishes.
Doodlebug Size: 100mm x 235mm
Suitable for Applicator Pad size: 115mm x 250mm
Diamond Oil is used for oil finishing of wooden floors with floor machine. The oil ensures an extremely hard wearing, dirt and water repellant surface. Diamond Oil is ideal for basic finishing of any unfinished, new and newly sanded interior woodwork. Content of solvent is less than 5 percent. Floor machine is recommended for the polishing of bigger areas.
Comes in a range of colours, Natural, White, Extra White, Sand Grey, Concrete Grey, Caramel Brown, Chocolate Brown, Smoke Brown and Carbon Black.
Since the product reacts with the tannic acid in the oak, the colour after application may vary depending on the concentration of tannin in the wood. However, it creates a very unique colour and Vintage appearance.
Step 1 - The wood must be clean, dry and free from dirt and grease. Apply an even coat of the stain with a brush or a short-haired paint roller lengthwise along the grain.
Step 2 - Apply at least 1 litre of stain to 10 m2 of wood. Clean tools in water after use.
Step 3 - Leave the stained surface to dry for approx. 24 hours at 20°C (the wood must be completely dry).
Step 4 - De-nib standing fibres with a fine abrasive polishing pad and vacuum clean the floor before the final basic treatment. Finish the wood surface with WOCA oil, Colour Oil, Oil Lacquer or soap.
Consumption: 8-10 m2/litre
Active Stain is water based and developed to produce special effect colours in oak wood, to create a very unique colour. The product is non corrosive. Active Stain reacts with the tannic acid in the oak. The colour may vary after application depending on the concentration of tannin in the wood.